Search results
Jump to navigation
Jump to search
- {{Note|'''Using radioless software often requires setup of a stanza in your iax.co1 KB (203 words) - 03:25, 22 January 2021
- ...enumber>''. Where <nodenumber> = the AllStar Link node of your system. ''Note that usb and the node number are separated by an underscore (_) character.' ...simpleusb.conf file from an older installation (i.e., ACID), take special note of the change in naming. When a exact match is not made, the settings that9 KB (1,281 words) - 01:26, 22 January 2024
- Note: This Bill of Materials is for the BOTH halves of the board.2 KB (263 words) - 04:17, 28 January 2019
- {{ Note|'''This only works for ASL distributions and may not exist on others. Use a2 KB (261 words) - 08:29, 18 January 2021
- Set your node password. Note: No special characters allowed, letters and numbers only.3 KB (528 words) - 16:37, 17 May 2021
- ''Note:'' A stanza is also called a context in Asterisk PBX terminology, particula2 KB (269 words) - 01:10, 20 January 2021
- {{ Note|'''You may already have a stanza named [iaxrpt] in your iax.conf. You may r2 KB (296 words) - 15:21, 22 February 2024
- ...5 and 6 many times. It takes a while to sort it all out, stick to it. Make note of the password prompt for the root user. Many first time Linux installers2 KB (354 words) - 03:40, 2 January 2022
- ..., you may use the Parrot Once COP method to enable one cycle of parotting. Note: The recording will start right away, the user should not unkey their micro2 KB (395 words) - 23:12, 26 January 2019
- ...generator until further adjustment does not increase the deviation. Make a note of the peak deviation at this point. ...our radio is a remote base or simplex node, use the half-duplex procedure. Note: if you have a URI, the automated setup procedure should have set the recei6 KB (981 words) - 03:49, 2 January 2022
- But note that you are not going to copy paste any instructions at the command line l Also Note: Your mouse will not function inside the CONSOLE window.6 KB (1,005 words) - 18:22, 29 March 2022
- # Note: If the call sign you are requesting is already registered with AllStarLink4 KB (699 words) - 04:33, 18 January 2021
- ...he switch may be TURNED OFF and the system will continue running normally. Note, if SW2-3 is ON during this procedure, the “Diode Calibration” process ...high, or slowly to indicate that the discriminator noise level is too low. Note, if SW2-3 is ON during this procedure, the "Diode Calibration" process will7 KB (1,098 words) - 18:08, 20 March 2022
- Note: The ASL 1.01 installer is a Network installer and still uses the '''dvswi3 KB (412 words) - 16:52, 5 September 2023
- ...master/VOTER-pcb/KiCAD-schematic/VOTER_2022-01-22.pdf schematic], you will note that there are two Audio Select lines (ASEL1/ASEL2) connected to the 74HC40 ...tive filters to be disabled on the VOTER client they are configured for. ''NOTE:'' this is only true if there is a valid host connection.19 KB (3,266 words) - 15:08, 23 March 2022
- Note that this feature simply selects the receiver with the best signal strength2 KB (359 words) - 16:40, 3 August 2019
- * Note that due changes in later versions of asterisk, you cannot simply drop this * \note Serious contributions by Steve RoDgers, WA6ZFT <hwstar@rodgers.sdcoxmail.co12 KB (1,768 words) - 17:12, 3 December 2022
- NOTE: Since the semicolon (';') is recognized by the ? - Portable tent (note different then standard ';')5 KB (795 words) - 21:25, 27 September 2018
- The '''DSPBEW''' versions have Jim's DSP/BEW feature enabled. Note that due to the size of this feature, the ''diagnostics menu'' is '''NOT''' *Attach the PICKIT2/PICKit3 device to J1 on the VOTER board. Note that Pin 1 is closest to the power supply modules (as indicated on the boar11 KB (1,818 words) - 18:15, 20 March 2022
- Note: although 'RPT_NUMLINKS' ''is'' an Integer count of links, it can also be t Note: We are interested in executing the function ONLY when the node connects. T8 KB (1,323 words) - 22:08, 21 February 2021