USBRadio Channel Driver
Chan_usbradio is a feature rich DSP radio interface. It requires more CPU than chan_simpleusb and therefor chan_simpleusb may be a better choice on smaller computers.
usbradio.conf
usbradio.conf setting are well documented in the configuration file itself:
;
; Usbradio channel driver Configuration File
;
[general]
[usb]
eeprom = 0 ; EEPROM installed: 0,1
; 0 = no (default)
; 1 = yes
hdwtype = 0 ; Leave this set to 0 for USB sound fobs modified using
; the instructions from usbfob.pdf. Use a setting of
; 1 is for Dingotel/Sph interfaces.
rxboost = 1 ; 0 = 20db attenuator inserted, 1= 20db attenuator removed
; Set to 1 for additional gain if using a low-level receiver output
rxctcssrelax=1 ; reduce talkoff from radios w/o CTCSS Tx HPF
; Do not change this, leave this as a 1
txctcssdefault = 100.0 ; Default TX CTCSS frequency, any frequency permitted
rxctcssfreqs = 100.0 ; RX CTCSS frequencies in floating point. This list is comma delimited. Frequency must be in table.
txctcssfreqs = 100.0 ; TX CTCSS frequencies in floating point, any frequency permitted. This list is comma delimited. Will follow the RX CTCSS Frequency.
;rxctcssoverride = 0 ; Set to 1 or yes to start out in carrier squelch mode
carrierfrom = dsp ; no,usb,usbinvert,dsp,vox
; no - no carrier detection at all
; usb - from the COR line on the USB sound fob (Active High)
; usbinvert - from the inverted COR line on the USB sound (Active Low)
; dsp - from RX noise using DSP techniques
; vox - voice activated from RX audio
ctcssfrom = dsp ; no,usb,dsp
; no - no CTCSS decoding, system will be carrier squelch
; usb - from the CTCSS line on the USB sound fob (Active high)
; usbinvert - from the inverted CTCSS line on the USB sound fob (Active low)
; dsp - CTCSS decoding using RX audio in DSP.
; rxdemod option must be set to flat for this to work.
rxdemod = flat ; input type from radio: no,speaker,flat
; no - RX audio input not used
; flat - Use RX audio from discriminator (before de-emphasis)
; speaker - use de-emphasized audio
rxsquelchdelay = 30 ; delayline in ms carrier squelch tail eliminator
rxondelay = 0 ; Number of 20mSec intervals following the release of PTT.
; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging"
; or "Relay Racing". A positive value here will instruct the usbradio
; driver to ignore the COR line for a specified number of 20mSec
; intervals following the release of PTT. Use this ONLY on simplex
; nodes, and leave commented out for repeaters or other full duplex nodes.
txoffdelay = 0 ; Ignore the reciever for a specified number of 20 millisecond
; intervals after the transmitter unkeys.
; This is useful when setting up a half-duplex link with an existing
; repeater, where you need to ignore the repeater's hangtime.
txboost = 0 ; Add transmitter audio gain boost: 0,1
txprelim = yes ; Audio processing on left output channel: no,yes
; no - Audio is not pre-emphasized and limited.
; Suitable for use on a microphone input
; yes - Audio is pre-emphasized and limited.
; Suitable for direct connection to an FM modulator
txlimonly = yes ; Audio limiting with no pre-emphasis on output channel: no,yes
; no - Audio is not limited.
; yes - Audio is limited.
; Suitable for transmitters with no limiting but with pre-emphasis.
txtoctype = notone ; Transmit tone control type: no,phase,notone
; no - CTCSS tone encoding with no hang time
; phase - encode CTCSS and reverse phase
; AKA ("reverse burst") before unkeying TX
; notone - encode CTCSS and stop sending tone before unkeying TX
; AKA ("chicken burst")
txmixa = composite ; Left channel output: no,voice,tone,composite,auxvoice
; no - Do not output anything
; voice - output voice only
; tone - CTCSS tone only
; composite - voice and tone
; auxvoice - auxiliary voice output at headphone level for monitoring
txmixb = no ; Right channel output: no,voice,tone,composite, auxvoice
; no - Do not output anything
; voice - output voice only
; tone - CTCSS tone only
; composite - voice and tone
; auxvoice - auxiliary voice output at headphone level for monitoring
; Audio filters - requires version newer than ASL_1.01
rxlpf = 0 ; Receiver Audio Low Pass Filter 0,1 2
; 0 - 3.0 kHz cutoff (Default) value for reduced noise and increased intelligibility.
; 1 - 3.3 kHz cutoff for increased high end, sibilance and brightness.
; 2 - 3.5 kHz cutoff for even more high end, sibilance and brightness.
rxhpf = 0 ; Receiver Audio High Pass Filter 0,1
; 0 - 300 Hz cutoff. (Default) value to reduce sub-audible signals for retransmission and in the receiver speaker.
; 1 - 250 Hz cutoff for additional received and retransmitted bass response.
; recommend using this filter with a CTCSS tone no higher than 186.2 Hz.
txlpf = 0 ; Transmitter Audio Low Pass Filter 0,1
; 0 - 3.0 kHz cutoff. (Default) value.
; 1 - 3.3 kHz cutoff for increased high end, sibilance and brightness.
txhpf = 0 ; Transmitter Audio High Pass Filter 0,1,2
; 0 - 300 Hz cutoff. (Default) value to reduce interference between voice and sub-audible signaling tones and codes.
; 1 - 250 Hz cutoff for increased bass response in transmitted audio.
; 2 - 120 Hz cutoff for special applications requiring additional bass response in transmitted audio.
; Not recommended due to the increased possibility of voice energy interfering with sub-audible signaling
invertptt = 0 ; Invert PTT 0 = ground to transmit, 1 = open to transmit
; This is the collector lead of the 2n4401 on the modified
; usb sound fob.
; please refer to the howto for the procedure to do this.
duplex=1 ; Full Duplex
duplex3 = 0 ; duplex 3 gain setting (0 to disable)
; loops receive audio from the sound card directly to the transmit audio
Configuration
Parallel Port
When setting chan_usbradio to use a parallel port for I/O you must set a definition for the port address in rpt.conf:
iobase=0x378 ; Parallel port address (using for cor/ptt & switches +dh-rbi - 378,278,3bc common Lpt 1,2,3
You must then define the parallel port pins used for I/O in usbradio.conf:
[usb] pp6=ptt pp11=cor
When configuring your usbradio node you MUST ensure that the name of the radio is the same in both rpt.conf and usbradio.conf.
Node names are in format of usb_<nodenumber>. Where <nodenumber> = the AllStar Link node of your system. Note that usb and the node number are separated by an underscore (_) character.
Example:
Your usbraido.conf file defines your usb radio as [usb_1000]. Your rpt.conf file would then have:
rxchannel = radio/usb_1000
If you are reusing the usbradio.conf file from an older installation (i.e., ACID), take special note of the change in naming. chan_usbradio may not work without first making this change to your usbradio.conf file.
Miscellaneous
Parallel Port Pin Numbers
More information regarding numbering of parallel port hardware pins to their software equivalents can be found at Parallel Port Pin Numbers