Remote Base: Doug Hall RBI-1: Difference between revisions
No edit summary |
No edit summary |
||
| (7 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
{{Obsolete}} | |||
The Doug Hall Electronics Model RBI-1 is frequency agile multi port remote base. It is possible to interface the RBI-1 to AllStar, but only on a PC. | |||
The | = Connections = | ||
The RBI-1 uses the first 3 pins of the parallel port and can not be changed. There is no other interface method built into the app_rpt software. If you have been using the pins for anything else, you will need to migrate them to higher pins than the first 3. See [[SimpleUSB Channel Driver#Parallel_Port|Parallel Port GPIO]] | |||
Parallel port pinout is as follows: | Parallel port pinout is as follows: | ||
:PP1 = data | :PP1 = data | ||
| Line 11: | Line 12: | ||
No buffering is required. Attach directly to the RBI-1's DB9 interface on the correct PP pins. | No buffering is required. Attach directly to the RBI-1's DB9 interface on the correct PP pins. | ||
= AllStar Settings = | = AllStar Settings = | ||
| Line 48: | Line 47: | ||
[memory29285] ;Stored presets for radio, | [memory29285] ;Stored presets for radio, | ||
;Format: (recall# xx) = (Freq 6 digits and decimal) (TX PL Tone ) ( CTCSS Tone ) (ofset + - S ) ( power l m h ) | ;Format: (recall# xx) = (Freq 6 digits and decimal) (TX PL Tone ) ( CTCSS Tone ) (ofset + - S ) ( power l m h ) | ||
init=224.660,100.0,-l ;initial freq/mode on start-up/boot - choose something safe in case of error. Not required. Can be remarked out. | init=224.660,100.0,-l ;initial freq/mode on start-up/boot - choose something safe in case of error. Not required. Can be remarked out. | ||
| Line 62: | Line 60: | ||
</pre> | </pre> | ||
It is more than convenient and desirable to put all of the control functions on | Tuning a agile remote base has a unchangeable prefix of (star 5) *5 | ||
It is more than convenient and desirable to put all of the control functions on your main published node and secure the node/audio on a private node you can disconnect, such as 1999. This makes it dis-connectable for periodic use and prevents you from the need to connect to the node in 'command mode' ie *4xxxxx to control it's agile interface. That can allow you to set it before connecting the node for audio as well. Always review and test macro/scheduler initiations of this before leaving it to run unattended. | |||
Note : | Note : | ||
There is a security log-in function for remote base control. | There is a security log-in function for remote base control. This not yet documented in the wiki [[Remote Base]] section. | ||
[[Category:How to]] | |||
Latest revision as of 15:54, 24 October 2024
The Doug Hall Electronics Model RBI-1 is frequency agile multi port remote base. It is possible to interface the RBI-1 to AllStar, but only on a PC.
Connections
The RBI-1 uses the first 3 pins of the parallel port and can not be changed. There is no other interface method built into the app_rpt software. If you have been using the pins for anything else, you will need to migrate them to higher pins than the first 3. See Parallel Port GPIO
Parallel port pinout is as follows:
- PP1 = data
- PP2 = clock
- PP3 = reset
No buffering is required. Attach directly to the RBI-1's DB9 interface on the correct PP pins.
AllStar Settings
In rpt.conf you will need to set lines in the nodes stanza:
[29285] ; replace 28295 with your node number
iobase=0x378 ; (for lpt1)
remote=rbi ; Doug Hall RBI-1
functions=funtions-remote29285 ; Function list from link (a list of agile working commands) - use your node number
memory=memory29285 ; 'system stored' radio presets, not required - use your node number
[funtions-remote29285] ;for rbi-1 use your node number
0=remote,1 ; Retrieve Radio Stored Memory Channel
1=remote,2 ; Set freq. VFO MMMMM*KKK*O (Mhz digits, Khz digits, Offset)
2=remote,3 ; Set tx PL tone PL Tone HHH*D*
3=remote,4 ; Set rx PL tone HHH*D*
40=remote,100 ; Rx PL off
41=remote,101 ; Rx PL on
42=remote,102 ; Tx PL off
43=remote,103 ; Tx PL on
44=remote,104 ; Low Power
45=remote,105 ; Medium Power
46=remote,106 ; High Power
51=remote,5 ; Long status query
52=remote,140 ; Short status query
67=remote,210 ; Send a *
69=remote,211 ; Send a #
;Not Required but noted:
[memory29285] ;Stored presets for radio,
;Format: (recall# xx) = (Freq 6 digits and decimal) (TX PL Tone ) ( CTCSS Tone ) (ofset + - S ) ( power l m h )
init=224.660,100.0,-l ;initial freq/mode on start-up/boot - choose something safe in case of error. Not required. Can be remarked out.
00=224.560,100.0,-l
01=224.460,114.8,-l
02=224.580,131.8,-l
03=223.980,100.0,-l
04=146.940,114.8,-lt
10=442.175,162.2,+l
11=444.475,114.8,+l
12=444.150,100.0,+l
;13=446.500,100.0,sl
Tuning a agile remote base has a unchangeable prefix of (star 5) *5
It is more than convenient and desirable to put all of the control functions on your main published node and secure the node/audio on a private node you can disconnect, such as 1999. This makes it dis-connectable for periodic use and prevents you from the need to connect to the node in 'command mode' ie *4xxxxx to control it's agile interface. That can allow you to set it before connecting the node for audio as well. Always review and test macro/scheduler initiations of this before leaving it to run unattended.
Note : There is a security log-in function for remote base control. This not yet documented in the wiki Remote Base section.